As an Amazon Associate I earn from qualifying purchases
- 20%

3d printer LCD unit MKS TFT24 contact display RepRap controller panel TFT 24 full colour show SainSmart splash display monitor

SKU: NMEQA6Q4VHLL Category: Touch Screen Panels

$16.72

Title: MKS TFT24 Contact Display

MKS TFT24 is a colourful contact display which is used independently on 3d printer.

This show is not any must set mainboard firmware however work collectively straight.

And it’s straightforward to interchange into your emblem and edit your native language.

Powerfully,it’s succesful to wirelessly management 3D Printer and assist Cloud printing.

Extra, it’s out there to self-define as much as 13 instructions .

Extra options as follows:

Packing Listing

1*MKS TFT24 Contact Display

1*Flat Cable

Wiring

Dimension

How one can assemble with mainboard.

Set the baud fee, guarantee each TFT and controller board are the identical.

1.MKS Collection mainboards

Equivalent to, MKS SBASE,MKS MINI,MKS GEN,MKS BASE, MKS GEN L,and many others.

(MKS TFT24 will not be out there to work with Ramps1.4/1.5/1.6)

Flash firmware to mainboard .( TFT show has up to date newest config inside already).

Join TFT show to AUX-1 of the board.

No must configure on board firmware,they are going to work collectively straight after wire.

The boards want a exterior 12V energy provide.

2.Firmware Improve

Please copy following paperwork to the basis of SD card.

(Please do not edit the paperwork identify.)

mks_pic mks_config mkstft24

Then, plug the SD card to the TFT and energy on. It is going to replace robotically.

3.Config

4.Mattress Leveling

Auto Leveling

After the machine assembles with a mattress leveling controller, then run leveling on TFT interface.

#The command of auto leveling (G29 is on the market for Marlin.

Whereas G32 is for Repetier and Smoothieware)

>cfg_auto_leveling_cmd:G28;G29;

Handbook Leveling

Handbook leveling is sweet for MB,i3 and many others machines. It’s out there to set 3,4,5 level .

#The purpose variety of guide leveling:(3,4,5 level out there)

>cfg_point_number:4

5.Filament Exchange

It’s straightforward to interchange the filament when it runs out.

You’ll be able to set temperature and the pace of filament in-out on config.

As following:

#the pace of filament changing(mm/min)

>cfg_filament_change_speed:1200

#the size of filament changing(mm)

>cfg_filament_change_step:5

#the min temperature of filament changing

>cfg_filament_limit_temperature:175

Then, right here is the steps to interchange filament.

1).On printing

pause—–more—–change—-in/out—–stop

2).Earlier than begin printing

set—–change—–preheat—–in/out—–stop

6.Print from Breakpoint

TFT has a one of many glorious options is ready to print from Breakpoint.

Beneath is the way in which to do it.

Firstly, set goal temperature of extruder and heated mattress, after which preheat.

Secondly, when preheat prepared, go dwelling .(Discover: if energy off occurs throughout working printing from breakpoint, please should dwelling .)

Thirdly, transfer extruder to the breakpoint which is on the market to set allowable error.

#Breakpoints continued enjoying Z-axis error setting

>cfg_breakpoint_z_error:0.2

Fourth, click on set, after which click on Proceed(Means Print from Breakpoint).

After that, select the file you need.

(When you pause the printing, and switch the printer off,

then it is going to resume to print from the pause level after energy on.)

7.Filament Outage Detecting

Join detecting swap to PB1 of TFT.

Set configuration to set off low degree or excessive degree out there.

#the extent sign of outage detection module PB1(low degree:0; excessive degree:1)

>cfg_PB0_PB1_Level:1

8. Auto off after Print Finishes

Allow this perform on config,and take concerted with PWC swap.

#whether or not set machine auto-off after print finishes(auto-off:1; NO:0)

>cfg_print_finish_close_Machine:0

9. MKS WIFI

MKS TFT helps WIFI distant management. Please set configurations.

As observe:

#wifi mode(AP:1; STA:2)

>cfg_wifi_mode:1

#wifi identify and password

>cfg_wifi_ap_name:MKS_wifi

>cfg_wifi_key_code:makerbase

#Dynamic entry IP

>cfg_ip_dhcp_flag:1

#IP/masks/gateway

>cfg_ip_address:192.168.3.100

>cfg_ip_mask:255.255.255.0

>cfg_ip_gate:192.168.3.1

10.Consumer-Outlined Perform

Specification: 3d printer LCD unit MKS TFT24 contact display RepRap controller panel TFT 24 full colour show SainSmart splash display monitor

Brand Name

Makerbase

Origin

CN(Origin)

Item Type

Display Screen

Model Number

MKS TFT24

Type

full calor touch screen display

Size

2.4inch

Support

multiple language

Available

user-defined booting logo

user-defined

13 commands

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “3d printer LCD unit MKS TFT24 contact display RepRap controller panel TFT 24 full colour show SainSmart splash display monitor”

Workhomeshop
Logo